You can access it through the link in the post above or from here: https://3dwarehouse.sketchup.com/social/model.html?id=676f0fe7-2afe-49c0-a0b7-2989ddc399db.

By clicking “Accept”, you consent to the use of ALL the cookies. If you did choose to keep them, you’d use the same method, but cut the grooves in the bed rail shelf wider to fit.

I have not put together the cut list for the full sized version, but your comment put that back on the radar screen. Can I ask what the paint color is?

Turned out that not all my panels were exactly 7 1/4″. Since I finished the bed, we’ve been on the lookout for a nightstand to match, but […], […] you haven’t seen the other posts on the making of this bed, start here. See my full disclosure here.

Symmetrical gables often are present, adding a pleasing sense of balance. Either way will work, particularly if you’re going to paint the bed. One of the big differences between my plan and the Ana White plan is how I attach the bed rails.

15 1/2” x 80 1/4” for backing, measure and cut the drawer bottoms to fit.

Afterwards, fit the 2×4 trim to the footboard, as shown in the diagram. I’m doing a variation of a plan from Ana White’s website. I shopped Home Depot for 2x4s, 2×6 and 2×8 as their “premier” lumber is actually pretty nice and a few cents more than the “construction” grade lumber. Use wood glue and 2 1/2″ pocket holes to attach it to the 2×2 at the top of the headboard.

Hi Eric, thanks for the note!

Thanks for the reply.

We had to make a couple extra trips to Home Depot, like most of the projects we’ve done.

The frames I made separate then screwed them into the header and footer for support. In no event will Tylynn Sattler or Bitterroot DIY be held liable for any loss or damage (including, but not limited to, indirect or consequetial loss, damage, personal injury, or death) from using or with connection to the use of this website. Square Farmhouse Table . You can also just use the measurement adjustments in this full bed post and adjust the Queen Plan in this post. I’m wanting to build this bed because most beds cost $400 or $500 and are pressed board. If you prefer, you can leave the 4x4s at their nominal size which is 3 1/2″ x 3 1/2″. Inside farmhouse floor plans, the kitchen takes precedence and invites people to gather together. For your convenience, the plans include everything you need to make this bed in a twin, full, queen or king (both standard and california king). This post may contain affiliate links. The design we picked was the same, but the doors cover the frames, so the drawers sit flush with the frame facing. I usually use brackets since it makes assembly and disassembly really simple whenever you have to move the bed. Bitterroot DIY is a participant participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to amazon.com. **You can find these at Home Depot in the fastener section. But opting out of some of these cookies may have an effect on your browsing experience. In your instructions you mention that its important so I wanted to learn and know more about that before I purchase the tools I need for the project! Date Night Dinner: Sambal Shrimp, Tangerine and Avocado Salad and Roasted Carrots, DIY Farmhouse Bed – Full Version | A Lesson Learned, Rustic Farmhouse Nightstand | A Lesson Learned, Making a Rustic Farmhouse Bed Part 3: Finishing Touches | A Lesson Learned, Rustic Farmhouse Table Plans | A Lesson Learned, Farmhouse Bed Plans: Part 2 | A Lesson Learned, Building a Moveable Workbench | A Lesson Learned. I screwed the whole thing together! Your email address will not be published. I will HAVE to put out a video about THAT adventure…yikes.

Post was not sent - check your email addresses!

It’s not possible, unless you’ve got superhuman strength, to hold the posts tight enough against the panels to get a tight fit. The diagrams are a view from the back. You can still access the old plans here. Otherwise the dimensions would stay the same. Let me know if that helps.

A drill guide is a cheaper alternative and the next best thing. Countersink the head of the screws and add glue to the joints.

I just found this post and I’m ecstatic to have my husband make this for us! As you can see in the plans, you need to drill pocket holes at both ends of the slat and secure it to the legs using 2 1/2″ screws. I’ll be starting this project tomorrow as part of a birthday gift for my girlfriend, it’s a little last minute so hopefully I can get it all done in time! Post author By Ed Hart; Post date September 30, 2013; 21 Comments on Farmhouse Bed Plans: Part 2; Ok, so I had some things come up that took my last couple of weekends, but I’m back on task with the bed! Fit the 2×4 cleats to the sides of the bed frame. In one of the boards, drill pocket holes along the top side. Desk: Mid Century Modern Scandinavian Desk, https://www.edhart.me/rustic-farmhouse-table-plan/, (8) 1” x 4” x 8’ Pine Board (Trim for Panels), (4) 2” x 4” x 8’ Boards (Top of Panels and Siderail Boxspring Supports), (6) 2″ x 4″ x 8′ (For Boxspring Supports), (2) 2” x 6” x 8’ Boards (Top of Headboard & Footboard), (18) #8 1 3/4″ screws (for bed rail fasteners), Drill with 3/8″ bit, 1/2″ bit & #8 counter sink bit (, Chisels (for mortising the bed rail hardware). I show my projet to one friend and he told me that the bed frame support is not enough strong to support the weight. A new rustic style bed from Pottery Barn will likely cost you over $1,000.

Modern Farmhouse Bed Plans The step by step plan follows, with diagrams and shopping lists and cut list.

Follow the instructions and pay attention to the diagrams and build the wooden bed in just one weekend, even if you are a beginner when it comes to woodworking. did you use wax or polyurethane? Drill pilot holes and insert 2″ screws into the side rails. Note that this is for the queen version. For the queen sized bed project, count on about $300 for lumber, screws and paint/stain. Toggle navigation.

How did you finish the wood? Let all the wood glue dry and then sand everything smooth. Also 2×10 for foot board not listed in materials. Do you think I will still be able to use those for the slats or should I exchange them for 2x4s? Any word as to when that will be? So here’s my next project! Thanks! I could not find untreated 4×4 posts at Home Depot or Lowes, so I went to a local lumber shop (it was a little hard to find) where I was able to order them.